ASME A112.19.2 pdf free download

ASME A112.19.2 pdf free download Ceramic plumbing fixtures
1 Scope
1.1 This Standard covers vitreous and non-vitreous china plumbing fixtures and specifies requirements for materials, construction, performance, testing, and markings. This Standard’s performance requirements and test procedures apply to all types of water closets and urinals that discharge into gravity drainage systems in permanent buildings and structures, independent of occupancy.
1.2
This Standard covers the following plumbing fixtures:
(a) bathtubs;
(b) bidets;
(c) drinking fountains;
(d) fixtures for institutional applications;
(e) lavatories;
(f) shower bases;
(g) sinks:
(i) laboratory sinks;
(ii) laundry sinks;
(iii) service sinks;
(iv) utility sinks;
(v) kitchen sinks; and
(vi) clinic sinks;
(h) urinals; and
(i) water closets.
1.3
In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; “may” is used to express an option or that which is permissible within the limits of the standard; and “can” is used to express possibility or capability.
Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
1.4 SI units are the units of record in Canada. In this Standard, the yard/pound units are shown in parentheses. The values stated in each measurement system are equivalent in application; however, each system is to be used independently.
Combining values from the two measurement systems can result in non-conformance with this Standard. All references to gallons are to U.S. gallons. For information on the unit conversion criteria used in this Standard, see Annex B.
2 Reference publications This Standard refers to the following publications, and where such reference is made, it shall be to the edition listed below, including all amendments published thereto.
CSA Group
B1 25.3-1 2
Plumbing fittings
B651 -1 2
Accessible design for the built environment
CAN/CSA-B1 800-1 1 ,
Thermoplastic nonpressure piping compendium
CAN/CSA-B1 81 .1 -1 1
Acrylonitrile-butadiene-styrene (ABS) drain, waste, and vent pipe and pipe fittings
CAN/CSA-B1 81 .2-1 1
Polyvinylchloride (PVC) and chlorinated polyvinylchloride (CPVC) drain, waste, and vent pipe and pipe fittings
C22.2 No. 0.1 5-01 (R201 2)
Adhesive labels
CSA Group/IAPMO (International Association of Plumbing and Mechanical Officials)
CSA B45.5-1 1 /IAPMO Z1 24.4-201 1
Plastic plumbing fixtures
ASME International (American Society of Mechanical Engineers)
A1 1 2.6.1 M-1 997
Floor Affixed Supports for Off-the-Floor Plumbing Fixtures for Public Use
A1 1 2.6.2-2001
Framing-Affixed Supports for Off-the-Floor Water Closets with Concealed Tanks
A1 1 2.1 9.1 2-2006
Wall Mounted, Pedestal Mounted, Adjustable, Elevating, Tilting, and Pivoting Lavatory, Sink and Shampoo Bowl Carrier Systems and Drain Waste Systems
A1 1 2.1 9.1 4-2006
Six-Liter Water Closets Equipped with a Dual Flushing Device
A1 1 2.1 9.1 9-2006
Vitreous China Nonwater Urinals
ASME (American Society of Mechanical Engineers)/CSA Group
ASME A1 1 2.1 8.1 -201 2/CSA B1 25.1 -1 2
Plumbing supply fittings
ASME A1 1 2.1 8.2-201 1 /CSA B1 25.2-1 1
Plumbing waste fittings
ASME A1 1 2.1 9.5-201 1 /CSA B45.1 5-1 1
Flush valves and spuds for water closets, urinals, and tanks
ASSE (American Society of Sanitary Engineering)
1 002-1 999
Performance Requirements for Anti-Siphon Fill Valves (Ballcocks) for Gravity Water Closet Flush Tanks
1 037-1 986
Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures
ASTM International
D 331 1 -06a
Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
ICC/ANSI (International Code Council/American National Standards Institute)
A1 1 7.1 -2009
Accessible and Usable Buildings and Facilities
UL (Underwriters Laboratories Inc.)
969 (1 995)
Standard for Marking and Labeling Systems
3 Definitions and abbreviations
3.1 Definitions
The following definitions shall apply in this Standard:
Air gap — the unobstructed vertical distance, through the open atmosphere, between the lowest opening of a water supply and the flood level of the fixture.